0

Gaskets & Seals

Is your engine sweating oil at a joint, or does the cylinder head need to come off during a project? Gaskets and seals keep oil, coolant, combustion gases and compression where they belong between the parts of the engine, exhaust and drivetrain. The category covers everything from oil seals and O-rings to complete gasket kits and gasket material for both daily drivers and tuned projects.

What gaskets and seals do

A gasket fills the small irregularities between two surfaces so the joint stays sealed under pressure and heat. Among engine gaskets and seals you will find, for example, head gaskets, intake manifold gasket kits, oil filter housing gaskets and timing belt cover seals. Rotating shafts are typically sealed with oil seals, while O-rings are used in fittings and housings, for example. For the drivetrain there are separate groups for gearbox, differential and transfer case.

How to choose the right gasket

Start with the engine code or the part number of the original part – fitment depends on engine and model year, not just the car model. Then consider:

  • Thickness: A head gasket affects the compression ratio, so the thickness should be chosen based on the engine build and any decking or resurfacing of the cylinder head or block.
  • Bore: With larger pistons, the gasket bore must match the new cylinder diameter, e.g. 83.5 mm on a Cometic head gasket for the Audi 2.5 TFSI.
  • Material: Multi-layer steel (MLS) gaskets can typically handle higher cylinder pressure and boost than soft gaskets, but often require flat surfaces with the correct surface finish.
  • Single part or kit: If several joints need to be opened, a complete kit, such as the Fel-Pro intake manifold kits for the Ford Mustang and Dodge Challenger, can ensure you are not missing a single gasket.

Exhaust, installation and gasket material

Exhaust gaskets sit at the exhaust manifold, headers and flange joints, where heat and vibration put them under heavy stress. New headers may require different gaskets than the originals, so check the flange shape. When installing: clean the surfaces thoroughly, check them for warping, and tighten to the manufacturer's torque and sequence. If no ready-made gasket is available, you can cut your own from gasket material sheets, e.g. for covers and low-pressure flanges.

Brands and engines in the category

Brands include Cometic Gasket, Fel-Pro, Victor Reinz, Vertex Pistons and Wiseco. The range includes parts for engines such as the Ford 302/351W and 4.6/5.4L V8, Nissan RB20/RB26DETT and Audi 2.5 TFSI, as well as a few motorcycle and ATV engines such as the Yamaha YFZ450R.

Frequently asked questions

Can I reuse an old gasket?

It is generally not recommended. A gasket is compressed and conforms to the surfaces on first installation, so it rarely seals as well a second time. This applies especially to head and exhaust gaskets, where pressure and heat are highest.

How do I choose the thickness of a head gasket?

The thickness affects the compression ratio and the clearance between piston and cylinder head. If the head or block has been resurfaced, or different pistons have been fitted, the thickness should be calculated from the actual measurements rather than just the original spec.

Should I use gasket sealant with a new gasket?

It depends on the gasket and the manufacturer's instructions. Many multi-layer steel and coated gaskets should be installed dry, while certain joints, e.g. where two parts meet at a corner, may require a small amount of sealant.

Why is a new gasket leaking?

Typical causes are warped or dirty surfaces, incorrect torque or tightening sequence, reused bolts or a gasket that does not fit the specific engine. Check the surfaces and the engine code before you install a new one.

Gaskets & Seals
View as Grid List
Sort by
Display per page

Air Crossover Gasket

fel1247S3
Fel-Pro 1247 S-3 Engine Intake Manifold Gasket Set
66,90 € excl. VAT

Air Crossover Gasket

felMS958171
Fel-Pro Chevrolet S10 Engine Intake Manifold Gasket Set
38,93 € excl. VAT

Air Crossover Gasket

felMS96491
Fel-Pro Honda CR-V MS 96491 Engine Intake Manifold Gasket Set
52,19 € excl. VAT

Air Crossover Gasket

felMS97290
Fel-Pro Volkswagen Jetta MS 97290 Engine Intake Manifold Gasket Set
14,77 € excl. VAT

Air Crossover Gasket

felMS95516
Fel-Pro Toyota Corolla MS 95516 Engine Intake Manifold Gasket Set
36,07 € excl. VAT

Air Inj Gasket

fel73679
Fel-Pro BMW 530i 73679 Secondary Air Injection Control Valve Gasket
12,78 € excl. VAT

Air Valve Gasket

ede3895
Edelbrock Repl Gkt Pro-Flo 4V
24,78 € excl. VAT

Alfa 17+ 690T Cylinder Head Gasket L

cgsC14192-036
Cometic Alfa Romeo 2017+ 690T 2.9L Bi-Turbo V6 .036in MLX Cylinder Head Gasket - 88.3mm Bore - LHS
126,85 € excl. VAT

Alfa 17+ 690T Cylinder Head Gasket R

cgsC14193-036
Cometic Alfa Romeo 2017+ 690T 2.9L Bi-Turbo V6 .036in MLX Cylinder Head Gasket - 88.3mm Bore - RHS
126,85 € excl. VAT

AMC 2.5/3.8/4.0/4.2L Timing Cover Kit

cgsC5047
Cometic AMC 2.5L Straight-4 3.8/4.0/4.2L Inline-6 Timing Cover Gasket Kit
28,05 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5674-040
Cometic AMC 290/304/343/360 Gen-2/3 V8 .040in MLS Cylinder Head Gasket - 4.140in Bore
123,37 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5674-027
Cometic AMC 290/304/343/360 4.140in Bore .027inch MLS Head Gasket
123,25 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5674-030
Cometic AMC 290/304/343/360 Gen-2/3 V8 .030in MLS Cylinder Head Gasket - 4.140in Bore
123,34 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5669-040
Cometic AMC 290/304/343/360 Gen-2/3 V8 .040in MLS Cylinder Head Gasket - 3.810in Bore
123,68 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5674-080
Cometic AMC 290/304/343/360 Gen-2/3 V8 .080in MLS Cylinder Head Gasket - 4.140in Bore
190,23 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5669-060
Cometic AMC 290/304/343/360 Gen-2/3 V8 .060in MLS Cylinder Head Gasket - 3.810in Bore
164,28 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5669-045
Cometic AMC 290/304/343/360 Gen-2/3 V8 .045in MLS Cylinder Head Gasket - 3.810in Bore
129,87 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5674-045
Cometic AMC 290/304/343/360 Gen-2/3 V8 .045in MLS Cylinder Head Gasket - 4.140in Bore
129,55 € excl. VAT

AMC 290-360 Gen-2/3 V8 Head Gasket

cgsC5674-051
Cometic AMC 290/304/343/360 Gen-2/3 V8 .051in MLS Cylinder Head Gasket - 4.140in Bore
129,55 € excl. VAT

AMC 304-401 V8 Exhaust Manifold Set

cgsC5161
Cometic AMC 304-401 V8 .043in Copper Exhaust Manifold Gasket Set - Dogleg Ports
53,06 € excl. VAT

AMC 390/401 Gen-3 V8 Head Gasket

cgsC5938-066
Cometic AMC 390/401 Gen-3 V8 .066in MLS Cylinder Head Gasket - 4.380in Bore
163,71 € excl. VAT

AMC 390/401 Gen-3 V8 Head Gasket

cgsC5937-027
Cometic AMC 390/401 Gen-3 V8 4.250in Bore .027in MLS Cylinder Head Gasket
124,34 € excl. VAT

AMC 390/401 Gen-3 V8 Head Gasket

cgsC5937-051
Cometic AMC 390/401 Gen-3 V8 .051in MLS Cylinder Head Gasket - 4.250in Bore
129,55 € excl. VAT

AMC 390/401 Gen-3 V8 Head Gasket

cgsC5938-075
Cometic AMC 390/401 Gen-3 V8 .075in MLS Cylinder Head Gasket - 4.380in Bore
163,75 € excl. VAT