0

Pistons & Piston Rings

Do your cylinders need to be bored out, or does your engine need to handle more boost than it did from the factory? This category brings together pistons, piston sets, piston rings, wrist pins and circlips for rebuilding and building engines – for you who assemble the engine yourself or are planning a bigger project.

Pistons, rings and pins work together

The piston transfers combustion pressure via the wrist pin to the connecting rod, while the piston rings seal against the cylinder wall and control the oil. Circlips hold the pin in place in the piston. You can choose complete piston sets or individual parts such as piston rings and wrist pins. If the bottom end also needs strengthening, connecting rods and bearings are typically part of the same project.

How to choose pistons and piston rings

Start with the engine's dimensions and purpose, then choose based on these criteria:

  • Bore and oversize: The piston must match the cylinder's finished size. The range includes, for example, standard size and oversizes such as .020 and .040 inch, and the final size depends on how the block is machined.
  • Compression and crown shape: Crown volume (e.g. -14cc or -21cc) and compression ratio affect how much boost and which fuel the engine can run. Valve reliefs may be necessary if you switch to a different camshaft.
  • Ring pack: Ring heights such as 1.0 x 1.0 x 2.0 mm or 1.2 x 1.5 x 2.0 mm must match the piston's ring grooves.
  • Coating: Some pistons have a coated crown or skirt, which can reduce friction and wear – the effect depends on the product.

In this category you will find Wiseco, JE Pistons, CP Pistons, Mahle and Mahle OE, among others, e.g. Mahle pistons for Dodge 12V and 24V diesel engines. Check piston-to-wall clearance, ring end gap and ring orientation according to the manufacturer's instructions before assembling the engine, and follow the recommended break-in procedure.

Frequently asked questions

Should I use standard size or oversize?

It depends on the cylinder's dimensions after measuring. If the cylinder is worn or scored, it is typically bored out, and the piston is chosen to match the finished size. Have an engine machine shop measure the block before you order.

Can I reuse the old piston rings?

This is typically not recommended. The rings wear in against the cylinder wall, and new rings normally give the best seal. If you replace the pistons or hone the cylinders, the rings should also be replaced.

Why is the ring end gap important?

The rings expand when they get hot. If the gap is too small, the ends can butt together and damage the piston and cylinder. The correct gap depends on bore, use and boost – follow the ring manufacturer's instructions.

Should wrist pins and circlips be replaced along with the pistons?

Piston sets often include pins and clips, but it depends on the product. Circlips should typically always be new, as they can lose tension when removed.

View as Grid List
Sort by
Display per page

Support Rail - 9298684

mhl9298684
Mahle MS 4.040-4.080 3mm Support Rail
12,77 € excl. VAT

Support Rail - 9298909

mhl9298909
Mahle MS 4.125-4.185 3/16in Oil Ring Support Rail
15,37 € excl. VAT

Support Rail - 9299225

mhl9299225
Mahle MS 4.600-4.630 3mm Support Rail
12,77 € excl. VAT

Support Rail - 9299226

mhl9299226
Mahle MS 4.310-4.350 3mm Support Rail
12,77 € excl. VAT

Support Rail - 9299227

mhl9299227
Mahle MS 4.250-4.290 3mm Support Rail
12,77 € excl. VAT

Support Rail - 9299228

mhl9299228
Mahle MS 4.500-4.560 3mm Support Rail
12,77 € excl. VAT

Support Rail - 9300686

mhl9300686
Mahle MS 4.165-4.205 3mm Support Rails - Single
11,60 € excl. VAT

Support Rail - 9301680

mhl9301680
Mahle MS 3.898-(LS1) 3mm Support Rail
12,77 € excl. VAT

Support Rail - 9301835

mhl9301835
Mahle MS 4.000-4.040 2mm Support Rail
12,77 € excl. VAT

Support Rail - 9301838

mhl9301838
Mahle MS 4.040-4.080 2mm Oil Ring Support Rail
12,77 € excl. VAT

Support Rail - 9301840

mhl9301840
Mahle MS 4.125-4.165 2mm Oil Ring Support Rail
12,77 € excl. VAT

Support Rail - 9301922

mhl9301922
Mahle MS 4.080-4.120 2mm Oil Ring Support Rail
12,77 € excl. VAT

Support Rail - 9301923

mhl9301923
Mahle MS 4.165-4.205 2mm Oil Ring Support Rail
12,77 € excl. VAT

Support Rail - 9301947

mhl9301947
Mahle MS 3.989-3.947 2mm Oil Ring Support Rail
12,77 € excl. VAT

Support Rail - 9302399

mhl9302399
Mahle MS 3.810-3.840 3mm Support Rail
12,77 € excl. VAT